In the third week of November, typical PPH Raffia prices ranged from 880 to 1,020 €/t, depending on the producer and grade. The price increase continued. The lowest prices were in the SCE region, where weak demand did not support price increases. However, in the MCE and NCE region, PP producers and traders made small price increases. There is availability, demand is weakening. December prices will move along with monomer prices.

Overmolding is commonly used in the production of electrical components, connectors, and electronic devices. Overmolded parts in these applications bond more closely, reducing the risk of physical failure during use. This process can also be used in the automotive industry to produce soft-touch handles, covers, and armrests.

In the third week of November, GPPS prices were in a range of 950 - 1,100 EUR/t. The cheapest prices were still measured in Poland The cheapest products came from import sources outside Europe. The availability of European-made materials is poor. Especially those used in the technical eld. The recovery in demand in the Far East is coupled with poor European availability. Further price increases are likely in December. HIPS prices were in a range of 1,000-1,200 €/t. The supply of European types is limited, but there are few imports from outside Europe. However, the impact of the epidemic is also being felt among nished products, with fewer year-end orders. Converters expect a weaker-than-usual December.

As a result of the expected weak demand in December, polymer producers will be forced to curb price increases or even reduce their prices compared to the current price level. Compared to early November, LDPE prices are now € 50-70 higher. This is due to poor availability, not strong demand. Although LDPE converters, mainly packaging manufacturers, reported a good order backlog, it was weaker than usual in November. The epidemic is also having an impact on orders, with less than the usual Christmas pre-orders for packaging materials. Converters' customers do not dare to stock up or take risks either. For the time being, the change in oil and naphtha prices compared to a month ago does not predict a more serious monomer price increase, the most likely price increase of 10-30 €/t is ethylene (C2) and propylene (C3). Thus, a signicant LDPE price increase of more than € 30-50 at the end of the year (December) would be a very unfriendly move towards plastics converters. Most polymer manufacturers are thinking of increasing prices compared to early November. However, nding the optimum rate of increase now requires great care. Due to the epidemic, converters and traders are also more careful with stockpiling. No big advance purchases are expected in December. Even if tight availability persists until the end of the year, and probably in the rst half of January. If polymer producers come out with too high prices in December, they will further reduce demand. There will be no time for correction. Converters place orders in the rst 2 weeks of December, followed only by logistics. Converters are likely to grant year-end holidays sooner, so the Christmas break will in many cases begin as early as December 14th.

Here are the market prices of various types of commodity plastics PE-LD, PE-HD, PP and PS in Central and Eastern Europe with a delay of 5 weeks. The data was processed by our partner myCEPPI.Are you interested in current prices for commodity plastics? You can order Weekly polymer price reports from our editors.

In the case of PP, the availability is good. Availability issues are only with the usual, inexpensive PPC with high melt ow index. That is, it is no longer available cheaply, under 950 €/t. The prices of almost all PP grades have risen over the past week, with the rise in polyethylene prices also dragging polypropylene grades. Meanwhile, PPH prices in the SCE region are more unchanged, and even very cheap offers have appeared in Northern Macedonia for Raffia grades. This, in turn, suggests that the rising price trend will not be sustainable in December.

Each month, we conduct hundreds of interviews and telephone calls with industry players – plastics converters, traders, resin manufacturers – and we are also present at the biggest regional plastics trade fairs and conferences.

Another critical difference is the number of materials. In two-shot molding, two or more different materials are used to create a part, while overmolding involves adding only one or two additional materials for bonding with the substrate or insert.

EPS prices were in a range of 1,010-1,090 €/t last week. The insulation material season is over. Demand is low. There was just a low number of transactions last week. In December, prices are likely to follow the price change in SM.

In the third week of November the natural ABS price range was 1,560-1,800 EUR/t. Prices are rising sharply. Price increases are not only a Central European phenomenon but also a world phenomenon. Which now affects all plastics used in engineering, from polycarbonate to polyamide. There was a converter that received a modied, raised price from its supplier three times from the quote at the beginning of the month to the order. As availability has narrowed dramatically and no change is expected in December, it is likely that even in January, the market will be characterized by extremely tight availability and high prices. It could even happen that the price of ABS will again exceed 2,000 EUR/t at the end of the year in the event that the prices of both SM and butadiene rise signicantly.

The choice between two-shot molding and overmolding depends on the part's design, application, and intended functionality. Both processes offer unique benefits, including improved functionality and aesthetics, reduced assembly time and costs, and increased durability. Manufacturers must consider these benefits when choosing the best molding process for their specific product. As a leading manufacturer in Taiwan, MING-LI provides a wide range of molding processes, including two-shot molding and overmolding, ideal for various product applications.

Two-shot molding is commonly applied to produce parts and products with multiple colors or materials. The automobile industry, for example, uses two-shot molding to produce dashboard parts with a soft-grip surface and hard buttons. The process can also be applied in the production of consumer electronics, medical devices, and packaging products.

This site uses Cookies to improve your browsing experience. we’ll assume you’re OK to continue. If you want to read more about this, please click Use & Disclaimer ,thank you.

Two-shot molding is a process used to produce plastic parts with two or more materials or colors. It combines two plastic injection molding processes in a single cycle; thus, it is also known as dual injection molding or two-component molding. The process involves molding two materials in a single machine cycle. The first shot molds the basic shape of the part, while the second shot adds the complementary details or color to the part in the same mold.

The information we collect in the process forms the basis of our weekly price report and market analysis; it feeds into our plastics industry company database; and it serves as the starting point for our multi-level consulting services for companies that need help sizing up, entering or navigating a specific market.

Two-shot molding allows manufacturers to incorporate different materials with different properties into a single component. This eliminates the need for secondary assembly, reducing production time and costs, and lowering the risk of assembly errors. Additionally, this process can improve the part's functionality and aesthetics.

The main difference between two-shot molding and overmolding is the order in which materials are placed into the mold. Two-shot molding inserts the first material into a mold cavity and follows it with a second material, which then bonds to the first material. In contrast, overmolding places a pre-molded substrate or insert into the mold cavity and then overlayers it with another material.

In the third week of November, LDPE prices ranged from 940 to 1,030 EUR/t. The Serbian and Belarusian LDPE producers also raised their prices signicantly. There is clearly a shortage in the market. Few transactions took place, partly due to availability and partly due to high prices. Most converters had already procured the feedstock needed for November earlier this month. We expect rising prices in December (compared to early November). However, continuing sharp rise in prices over the last 2 weeks is unlikely. The change in prices will slightly exceed the increase in monomer prices. Supply will remain tight in both December and the rst half of January.

Overmolding is a process used to combine two or more different materials to create a single component. This process involves injecting molten resin into a pre-molded part to create a final product with enhanced functionality and aesthetics. Overmolding is also known as insert molding or multi-shot molding.

In the third week of November the prices of PPH IM non-special grades with low and medium ow melt index were in a range of 870-950 €/t last week in Central Europe. They increased slightly compared to the previous week. The prices of products with a high ow index were in a range of 900-990 €/t. The cheapest prices were measured last week in the SCE region. Demand is weaker than usual in November. This is due to the fact that there are fewer Christmas pre-orders and even in many cases they have been completely missed in the SCE region. Due to weaker-than-expected demand and rising feedstock prices, quite a few smaller converters plan to have a longer Christmas shutdown this year. They are waiting for what January will bring. As a result, only a small price increase in December, not exceeding the change in the price of propylene monomer, is likely in December.

The process involves placing an initial substrate in a mold cavity. Then, a second material is injected over the substrate with the help of another injection molding tool. The two materials bond together, forming a single unit, with the base material providing the structure and strength while the overmolded material forms the outer layer.

myCEPPI – a new voice and new approach on the plastics industry consulting and business intelligence market. With our expert advice, you can get a detailed, up-to-date and tailor-made picture of the Central and Eastern European plastics market and its main trends, data, news and key players.

In the third week of November, HDPE (100) prices ranged from 990 to 1,060 EUR/t. Due to the end of the pipe season, demand is steadily weakening. In December, prices will rise due to the expected monomer price increase. In the third week of August, the range of LLDPE C4 prices was 860-1,000 €/t. Prices have risen slightly, mainly due to a contraction in supply due to the shutdown in Porvoo. Second, prices followed the generally rising trend of PE prices. However, unlike other polyethylene grades, there is availability, although supply is limited.

In the third week of November HDPE prices were in a range of 860-1,000 €/t in Central Europe. What happened was already visible last week. Both the bottom and top of the price band rose after the Serbian polymer producer also raised prices earlier this week. Availability is poor here as well, and there is even a shortage of lm grades in the Baltics. Demand was not strong either, there were few transactions. Typical transaction prices ranged from 830 to 920 EUR/t last week. In December, prices are expected to rise compared to early November prices. it is likely that the current price level will continue to roll into November. In detail

Here are the market prices of various types of commodity plastics PE-LD, PE-HD, PP and PS in Central and Eastern Europe with a delay of 5 weeks. The data was processed by our partner myCEPPI.Are you interested in current prices for commodity plastics? You can order Weekly polymer price reports from our editors.

Unexpected turbulence has developed around polyethylene grades in recent weeks. The shutdown of SABIC's Wilton plant was theoretically offset by the restart of LyondellBasell's plant in Aubette. However, a consistently more expensive product cannot replace the lost cheaper one in Central Europe. The situation was further aggravated by the low availability of LDPE in Serbia, Romania, Hungary and Slovakia. The shutdown of Borealis' Finnish plant only exacerbated the situation. Thus, last week - in the second half of November - LDPE prices increased signicantly by 40-70 €/t in Central Europe. Producers (Belarus and Serbia) who offered their products at the lowest prices so far have raised the most. Overall LDPE demand is not strong. There is no panic in the market. Companies do not buy at these increased prices. Most are condent that uncertainty over the short month in December and the covid epidemic will also dampen demand. Demand is also reduced by the fact that at this increased price level, it is no longer worthwhile for contracted customers to maximize their bonuses either. Now plastics converters are buying who procure on a spot basis or postpone their purchases until the second half of the month. They are now forced to buy at increased prices to cover their production. Not only did the price of rst-class LDPE materials rise, but so did the prices of “near to prime” and “off-grade” materials. In the case of HDPE, there were also producers who increased their prices to a lesser extent.

Be informed about the latest news and developments in the plastics industry or follow us on social networks. You can unsubscribe at any time.

Personal registration will allow you to take a use of PlasticPortal services. You can post 1 classified ad free of charge.

The polystyrene market, with the exception of EPS, is now driven by shortages. The European supply of GPPS, HIPS and ABS is tight. The price of the latter is racing sharply upwards in the spot markets. But this steep price increase is typical of plastics used in all technical elds (PC, PA, POM, etc.). In addition to demand from the Far East, European demand is also picking up. While traditional trade chains and routes are difficult to operate, in some cases they have been disrupted. As a result, arbitrage opportunities have also narrowed. We also expect tight supply in December and the rst half of January and further rising prices for ABS.

Manufacturing industries rely on various molding processes to produce high-quality products efficiently. Two of the most commonly used methods are two-shot molding and overmolding. These molding processes may seem similar at first glance, but they differ in several key ways. In this article, we will explore the differences between the two processes, their benefits, and their applications.

In the third week of November, mLLDPE (C6) prices were in the price range of 880-1,160 EUR/t. They did not change compared to last week. This is because they are used in relatively small quantities by converters and have relatively large stocks. Not a typical spot market product. Availability is good.

PPR prices for the third week in November were in a range of 990-1,090 EUR/t last week. They did not change compared to last week. Demand is weaker than usual, the pipe season is over, and there is also less PPR in the IM area.

In the third week of November typical PPC prices were in a range of 950-1,070 €/t in Central-Europe. The typical transaction price range was 970-1,050 €/t. Availability of grades with high melt ow index in spot markets is poor, however, there are no serious supply problems. In December, prices will follow the propylene monomer.