It is really situation-specific to decide which process suits a product better. Two-shot injection molding is usually a more expensive process but provides the designer with higher manufacturing precision and a better mechanical bond.

When compared to conventional molding and assembly, or even with modern processes such as insert molding, two-shot molding provides very accurate manufacturing. As the semi finished product does not need to be removed from the mold in between steps, there is no chance of material misalignment. If thermal effects are properly controlled through good product design, the final result can truly be as accurate as the mold itself.

As the name suggests, this process makes use of two injection shots instead of just one as in conventional injection molding. A special mold is used in this process that accommodates the requirements of these two shots. The mold and its supporting systems are designed to perform two shots without having to remove the partially finished product in between steps.

When investigating manufacturing methods for a future product, injection molding professionals will quickly find that overmolding and two-shot molding are very similar processes. In both processes, molding is done in multiple steps, using multiple materials. Both processes have similar benefits as well, such as savings in time and costs on secondary assembly steps. They do, however, have enough differences to give each merit in its respective field.

The rapid tooling process involves the creation of a mold using aluminum or soft steel, a stocked mold base, and hand-load inserts. Rapid tooling is one of the best methods for fulfilling small batch orders meant for use in marketing samples, product evaluations, and process design.

Two months ago, I was super stressed by an urgent plastic molding project. Our customer desperately wanted 100 sets at very short notice in order to run testing with real materials, even though normal production would have taken more than six months. None of our preferred moldmaking suppliers could help us, given the deadline. Luckily, one of my friends recommended 3ERP to us by chance.

In cases where adhesion combinations are unknown, an adhesion test needs to be done before two-shot molding can commence. In cases where the inherent bonding ability is not sufficient, undercuts, shoulders or grooves may be added into the design to lock the two components together.

Two shot molding enables the designer to utilize the best of multiple materials. Engineering plastics may have many good, but vastly different properties. The designer can combine good structural properties of a hard plastic with the soft and appealing nature of a different material to achieve the desired results accurately.

Every quarter, we order approximately 20 sets of plastic enclosures for our device from 3ERP. The enclosures were initially made by urethane casting, but Ronan came back to me with the idea of using an aluminum mold, which allowed me to get a few hundred moldings. We decided to move to this process. The T1 samples weren’t good enough, as we got some shrink marks, but this was quickly sorted out when we received the T2 samples.

Can you imagine attempting to make prototype tools for over 30 components in just two months? Our customer desperately needed 200-300 sets of tail lights for testing, but mass production tools wouldn’t have been ready for eight months. They needed a solution to get good quality moldings by their deadline and at a much lower cost than production tools.

Overmolding utilizes a simpler mold setup, but can not provide the same repeatability, precision and process stability as two-shot molding does. The unit is the cost is however usually lower than that of a two-shot operation. Overmolding does provide the designer the ability to mold over a metal substrate (e.g. scissor blades), which makes it ideal for certain applications.

For this tail light project, we needed to fabricate a housing, reflector, light guide, bezel, an outer lens, and other components in a short period of time. The overall assembly size was about 600 x 400 x 150 mm, which is relatively large and the customer wanted to test real materials. In this case, 3D printing, CNC machining, and vacuum casting were not suitable, so prototype molding was the only option. Click to view this case

Though it features multiple benefits, steel is a more expensive tooling material than aluminum and requires more turnaround time to produce molds and prototypes.

Plastic storage containers can be manufactured with this process. Different colours can be added, along with rubbery edges to seal lids, or soft container surfaces to protect contents.

In general, two-shot injection molding requires a more complicated, and therefore expensive setup. Two-shot molds typically have a rotating platen that holds the semi-finished product. While this is a more complicated mold design, it does provide the process with higher manufacturing precision. As the product does not need to be removed and handled between steps, this eliminates human or machine error.

An ideal choice for prototyping, aluminum mold tooling provides a cost-effective way to produce molded parts. Since they are easy to cut, aluminum molds can reduce tooling costs by 15–25% compared to other mold materials and reduce cycle times by up to 40%. This translates to a faster turnaround for our customers.

When considering materials to be used for two-shot molding, it is important to take the chemistry into account. Not all materials bond perfectly, but some may form a very strong molecular bond. An adhesion compatibility chart is given below.

Two shot injection molding works well here due to the desirable properties of plastic in a water environment. Hard-wearing base areas can be combined with softer seal surfaces.

Plastic electronic products with LED’s incorporated into the design can be effectively produced with two-shot molding. A translucent insert can be molded into the design to spread or colour the LED light.

In two shot injection molding, a product is formed by injecting two different materials into the same mold. These materials are not injected simultaneously, but rather in succession. It is, however, done in one manufacturing step in which the product is not ejected from the mold between the two shots.

After the first step, the mold opens and the platen containing the product rotates 180 degrees on a horizontal axis to align with the sprue of the second step. In this step, the first cavity is sealed off from any injection. As the sprue of the second material is now aligned with the runner for the second cavity, the second shot now commences to mold the remainder of the product.

The molds used in two-shot molding consist of different tool sets. In a rotating platen setup, the tools share the same core, but not the same cavities. The runners must be designed as such to be shut off during the molding steps in which it is not active.

Items such as toothbrushes can be perfectly molded with two-shot molding. A rigid base plastic can be used with a softer rubber second shot for better grip and coloration.

Steel is a sturdy, solid, high-quality tooling material, though it is not suitable for all applications. Steel molds have a longer life cycle than aluminum and are therefore ideal for high-volume production. Steel can also be used to produce molds from engineering-grade plastics that are resistant to abrasion and corrosion.

Aluminum evenly dissipates heat, which provides dimensional stability in tooling. This significantly reduces deformation and produces less waste during the production process. It is important to note that aluminum is not as strong as steel, so it has a shorter life cycle and is less useful in high-volume processes.

Two shot injection molding offers freedom to the designer, as it negates the use of multiple steps in manufacturing. It provides molding manufacturer with many advantages such as lower manufacturing cost, better aesthetics and ergonomics, superior mechanical bonds and lower production times. Many products, such as toys, automotive parts, medical equipment, containers and toiletries can be manufactured using this method.

Products manufactured using two shot injection molding exhibit great mechanical properties. During the molding process, different levels of the product form a molecular bond given good material selection. This bond is often stronger than conventional molding and assembly, and even stronger than other advanced methods such as over- and insert molding.

At 3ERP, we typically create rapid molds by CNC machining and EDM, though we also sometimes use additive methods such as 3D printing technologies.

A deciding benefit of two shot injection molding is the saving on production time. As multiple levels of a product can be added in this process, there is often no need to do secondary assembly of the item. What would have been a complete secondary step in manufacturing with conventional injection molding, can now be done in one combined molding process.

The process starts similar to normal injection molding with the mold closing to form the first cavity. In this initial setting, the runner for the first cavity is aligned with the sprue of the base material, while the runner for the secondary step is sealed off. The first material is then injected and fills the first cavity.

Although we had to invest more for the mold, we now save 70% compared with urethane casting, and we can use UV-resistant ABS to keep the color stable. Overall, I am very happy with the solution.

The plastic injection molding industry has come a long way since its beginning. It has grown a lot in terms of its efficiency and cost effectiveness, but also in new and innovative ways to manufacture products. One of these innovative ways is the process of two-shot molding. This process is sometimes known as multi-material injection molding, 2 colour injection molding, 2k injection molding or double-shot injection molding.

In no instance during this process is the product ever removed, shifted or moved in the mold. The final product is therefore manufactured as accurate as the mold itself, barring any post process imperfections due to elements such as irregular cooling.

3ERP has a fantastic mold design team. They managed to finish the mold design within 10 days and started to fabricate the molds right after that. I was surprised that more than 60 items, including some big parts, were completed to a decent standard within two months. Our customers eventually received the moldings to run their testing. 3ERP saved our business!

Medical equipment such as bone saws can be manufactured using two-shot molding. Rubber grips are very important in the function of this equipment. Two-shot molded items also improve hygiene as there are fewer crevices where sub-parts interface, as compared to conventionally assembled items.

Products that are manufactured in a two-shot process can look very good while also retaining the structural properties that are required from them. In this process, the load-bearing structural part can be molded in the first step while the finishing touches can be added using a more appealing material in the second step.

The process of two-shot injection molding can manufacture ergonomically designed products to perfection. Structural plastic can easily be covered or added on using materials that are more suited for human interface. Soft, rubbery material is better equipped for the human hand as it provides better grip and a softer touch.

Traditional tooling is often prohibitively expensive for small projects. Our custom rapid tooling service is a cost-effective, low-volume alternative in situations where large volumes of the part won’t be needed in the future. The rapid production tooling process is commonly used in industrial settings for prototyping solutions or for diagnosing design issues, providing an easy introduction to mold making.

This is where two shot injection molding really come to its own. Two-shot molding enables a production line to maufacture more complex products, with less production steps than ever before. Consider the conventional injection molding process: If a certain product was to consist of two different materials, they would have had to be molded seperately, in two different molds, followed by a manual assembly step. In two-shot injection molding, these two constituents are not only molded in one mold setup, but they are also fused together, eliminating the need for any assembly.