Another useful element of the gas bubbles molded inside foamed parts can be the inherent thermal insulation and sound deadening qualities. The ability of heat and sound to move through these parts is inhibited in the same way construction materials utilize trapped air pockets to perform the same task. In general the insulating qualities of foamed parts increase as more blowing agent is utilized and more resin is removed from the final part.

Injection mold prototyping is the process of developing a tool to expedite a molded part. Spectrum can create your part as close to the intended product design and functionality as possible using your requirements.

As a single-source partner, we can support your complex surgical device throughout the product lifecycle, from design for manufacturability to development to validation and manufacturing.

As medical treatments become less invasive, medical devices are getting smaller. We have the expertise to do precision micromolding, including specialized equipment, tool designs, and measurement systems.

Implantable and bioresorbable materials pose unique preparation, processing, and handling challenges. As a pioneer with these materials, we have expertise and dedicated resources for manufacturing implantable and bioresorbable plastic components.

Polyetheretherketone (PEEK) is a high-strength, high-temperature thermoplastic with superior mechanical and chemical properties ideal for injection molding applications.

As a result these expanding gases form a cellular matrix of gas bubbles inside the rigid plastic part, aiding in filling and packing out the part cavity. This dramatically decreases the fill pressure required to mold a part.

Our silicone molding capabilities include liquid injection molding as well as silicone rubber transfer molding, overmolding, and liquid injection molding.

Standard plastics design rules restrict designers to thinner walls when adding features like ribs and bosses to avoid cosmetic sink marks. A rib/wall ratio of 65% is a long-standing and trusted rule. In foamed parts these rules can be significantly modified as the process will support packing out features well above 100% rib/wall ratios. Structural foam also allows more leniency for varying nominal wall thicknesses, another design aspect limited by traditional design rules.

Part designers should be aware there are some added costs to the process. Structural foam parts require thicker wall geometries than traditional molded parts in most cases. Foamed parts are typically designed at wall thicknesses of 6mm or 0.25“ as thinner walls tend to inhibit the ability of the foaming reaction to occur. This means in most cases the conversion to foam requires an increase in part weight and resin usage – though keep in mind that some of that is offset with the cell structure. Thus weight and resin savings may not hold true when compared to the same part molded traditionally. The increased wall thickness and process also dictates the need for longer cycle times over traditional molding which can add to part cost.

The aesthetic requirements of the part also need to be considered. The foaming activity in the process typically compromises the appearance of the viewed surfaces of the part. While this can be accepted for internal components or other non-esthetic parts it is typical to paint structural foam panels as a secondary operation to create visually acceptable parts. This can be accomplished with a standard multistep painting process to prime, finish and spatter coat per the part requirements.

By consolidating several assembled or welded components into a single molded part it is possible to yield significant cost savings that can quickly offset the price of a mold tool or painting.

Spectrum is the starting point for medical device development requiring critical components. Our off-the-shelf tubing and components are available in our Component Webstore to accelerate the design and development of your next project.

The cellular gas pockets molded into the parts can also be useful to designers in certain ways. While only 0.5-4% of blowing agent is added to the raw resin, the resulting cellular void space inside the part can offset a significant amount of resin usage in a given part. Depending on the part design and process it is typical to reduce part weight on the order of 7-20% when compared to molding the same part without structural foam. This results lighter parts and lower resin costs.

Structural foam molding has been one of Mack Molding’s competencies for decades. With in-house design and processing expertise Mack can support our customer’s foamed part opportunities, ensuring they are on a path to utilize the benefits of this process. Below are some examples of structural foam production parts and the benefits they offered.

Another benefit of realizing lower process pressures is that the resultant parts will have less molded in stress and in turn lower distortion and warp out of the mold.

Our injection-molded solutions include premium, high-quality components and fully assembled medical devices. We have years of experience with complex molding projects working with highly engineered performance medical plastics.

A common and useful variation to the plastic injection molding process is called structural foam molding, which can be utilized to mold part geometries and flow lengths that traditional molding would not be able to accommodate.

When calculating press sizing in injection molding generally a given part will require 3-4 tons per square inch of projected area. By comparison, the structural foam process requires closer to 1 ton per square inch. This means that a straight injection part running in a 1,000 ton press could run in a 300-ton press with structural foam. This can be an important factor to consider since press size is a primary driver of molded part cost.

This process uses the same basic steps as traditional injection molding with one important distinction – a chemical blowing agent is added directly into the resin stream feeding the press at a ratio of 0.5% to 4% by weight. The blowing agent undergoes a chemical reaction while filling the mold that produces gases inside the molten resin.

In some cases light sanding may be required on the part surfaces to smooth out heavily foamed areas. Because of these specific requirements it is beneficial to identify if structural foam will be utilized to produce a part early on in the design process. While most resins can be foamed there are specific resin grades on the market designed to work extremely well with chemical blowing agents.

We have decades of experience molding onto metal and other substrates. Combining properties of different materials, such as strength and flexibility, can create more intricate designs for aesthetics, branding, or ergonomics.

While many parts can be candidates for structural foam molding the process is utilized especially well when the aforementioned part geometry challenges arise in a part. While this can manifest in several design scenarios a common example would be when internal frame geometries that may be sheet metal or castings are redesigned as molded parts. The complex geometric detail and size of these assemblies often turn into molded parts that cannot be made without structural foam. Since these components are typically not viewed by the end user the secondary paint and decoration steps are usually not needed.

Multishot injection molding requires expertise in material interactions and understanding of how to combine multiple materials in one mold. We have the capability to support complex components from concept to production.