In the world of plastic injection molding, a short shot is a common cosmetic defect that can occur when the mold cavity isn’t entirely filled during the molding process. This often results in an unfinished part with visible flaws. At JATCO, Inc., a trusted California-based custom injection molder, we understand the intricacies of short shots, their causes, and how to address them effectively.

Commercially, injection moulding offers a flexible, consistent and cost-effective process of manufacturing that allows for rapid production of parts in a range of materials. Once the process has been set up and tested, machines can produce thousands of items per hour and once the mould is created (which is the most expensive element) the cost of production per component is relatively low.

If sections of different thicknesses are required, make the transition as smooth as possible using a chamfer or fillet. This will allow the material to flow more evenly through the mould.

Short shots can arise from various factors, including low injection pressure, material flow restrictions, complex flow paths, inadequate venting, material variations, and more.

The outer diameter of the boss should be 2x the nominal diameter of the screw or insert and its inner diameter equal to the diameter of the core of the screw.

Trapped air in the mold can inhibit the flow of the material during injection, resulting in an incomplete part. Good design can improve the flowability of the melted plastic.

As the plastic shrinks, it applies pressure on the mold. During ejection, the walls of the part will slide and scrape against the mold, which can result to drag marks.

Draft angle is a taper applied to the vertical walls of the component to be moulded to assist with releasing the part. Walls without draft angle may become stuck in the mould and will have drag marks on their surface.

Bosses consist of cylindrical projections with holes designed to receive screws and other fasteners and assembly hardware, they are very common in injection moulded parts as they are used as points of attachment or assembly.

When the interior of a part solidifies before its surface, a small recess in an otherwise flat surface may appear, called a sink mark.

To avoid warping and sink marks on the part as the melted material cools down it is important to have uniform wall thicknesses and avoid thick sections if possible.

Here at UNSW we have 2 CR Clarke desktop injection moulders great for learning, testing and experimenting with the process!

Injection moulding is a manufacturing process that melts, injects and sets plastic into a metal mould. The plastics used by injection molding processes are relatively cheap and can be used to achieve a wide variety of properties, so injection molding is popular for creating many packaging and consumer products, like LEGO!

Contact our Steven Ames Director of Sales 209-497-4290 Steven.ames@jatco.com if you have any questions or need a quick quote!  You may also click here to contact us via our site form.

It’s crucial to note that addressing one issue can sometimes lead to others in the molding process, requiring comprehensive examination and consideration of all mold design specifications. Rest assured, our experts at JATCO, Inc. are committed to resolving short shots before any defective products leave our manufacturing floor.

Thick sections can lead to various issues such as warping and sinking. Reducing the maximum thickness of the design can be achieved by making the thicker sections hollow is essential. To improve the strength of these sections, ribs can be used to create structures that are of equal strength and stiffness but with reduced wall thickness and weight.

When 2 flows meet, small hair-like discolorations may develop. These knit lines affect the parts aesthetics, but also they generally decrease the strength of the part.

For interior edges, use a radius of at least 0.5 x the wall thickness. For exterior edges add a radius equal to the interior radius plus the wall thickness to ensure constant thickness everywhere. This can also help to stop stress concentrating in the sharp corners which can cause weaker parts.

To remedy these occurrences, our skilled team employs a range of solutions such as eliminating air traps, adjusting mold and melt temperatures, selecting appropriate press sizes, modifying part geometry and much more.  Bottom line is that it’s important to fully evaluate the quality of plastic products we manufacture and make absolutely certain that the customer gets the highest grade product!

Undercuts refer to part features that cannot be manufactured with a simple 2-part mould because material is in the way while the mould opens or during the ejection of the part. Avoiding undercuts all together is usually the best options as they add cost, complexity and maintenance requirements to the mould.

JATCO is a global leader in plastic injection molding with a heavy focus on value creation. We are a one stop shop which offers product(life) consulting, design, production, warehousing and distribution solutions for just about any project.

When adding text choose embossed text over engraved text as it is more economical when creating the mould. Raising the text 0.5mm above the part surface will ensure the letters are easy to read.

Injection moulding typically produces parts with tolerances of +/- 0.25mm. Tighter tolerances can be possible in certain situations but increase the cost of manufacture dramatically.

When even the maximum recommended wall thickness is not enough to meet the functional requirements of a part, ribs can be used to improve the strength and stiffness of a part.

When designing ribs, use a thickness equal to 0.5 x the main thickness, define a height smaller than 3 x the rib thickness and use a base fillet with a radius greater than 1/4 x the rib thickness. Also make sure to add draft angle!

Redesigning the part to remove undercuts or moving the part line can be possible solutions to make the design more feasible.

When certain sections cool (and as a result shrink) faster than others, then the part can permanently bend due to internal stresses.

The uniform wall thickness limitations also applies to edges and corners; the transition must be as smooth as possible to ensure good material flow through the mould.