If the length of the runner to each cavity is different in this case, the cavities may not be filled simultaneously, so that dimensions, appearances or properties of the moldings are often different cavity by cavity. Therefore the runner is usually designed so as to have the same length from the sprue to each cavity.

Multilayer flexible packaging factory with running business on sale Product Milk Packaging Film LDPE / LLDP / MLLDPE Edible Oil Packing Film Material used:-LDPE/LLDPE/HDPE Industr......

Cylinder Engraving Factory: We have the cylinder engraving factory as follows: A) Art working: 1. G5 Computer, 2008 2. PC Computer, 2008 3. Artpro Software, Upgrade 2008 4. Epson Pr......

A mold is a hollow metal block into which molten plastic is injected to from a certain fixed shape. Although they are not illustrated in the figure shown below, actually there are many holes drilled in the block for temperature control by means of hot water, oil or heaters.

While molten plastic is flowing in a mold, the machine controls the moving speed of the screw, or injection speed. On the other hand, it controls dwell pressure after molten plastic fills out cavities.

Molten plastic flows into a mold through a sprue and fills cavities by way of runners and gates. Then, the mold is opened after cooling process and the ejector rod of the injection molding machine pushes the ejector plate of the mold to further eject moldings.

Molding condition means cylinder temperature, injection speed, mold temperature etc. set in a molding machine to obtain required moldings, and the number of combinations of conditions is innumerable. Depending on the conditions selected, the appearances, dimensions, and mechanical properties of the molded products change considerably.

The method is suitable for the mass production of products with complicated shapes, and takes a large part in the area of plastic processing.

Password must be between 4 and 15 characters long, and may consist of hyphen (-), underscores (_), dot (.), and asterix (*).

Reprocessed materials are not solely used as materials for molding but usually used after blending with virgin pellets, since there is possibility of deterioration in various characteristics of the plastics because of the initial molding process. The maximum allowable limit for the ratio of reprocessed materials is about 30 %, because too high ratio of reprocessed materials may spoil the original properties of the plastics used.

Injection molding is a method to obtain molded products by injecting plastic materials molten by heat into a mold, and then cooling and solidifying them.

Injection molding machine is divided into 2 units i.e. a clamping unit and an injection unit. The functions of the clamping unit are opening and closing a die, and the ejection of products. There are 2 types of clamping methods, namely the toggle type shown in the figure below and the straight-hydraulic type in which a mold is directly opened and closed with a hydraulic cylinder.

A running factory manufacturing machinery is for sale at Gujarat. Unit established since 1987 manufacturing plastic processing machinery. The proprietor desires to retire and hence ......

Compounding Facility machines and Plant. 1) Two Extruders : I) 70 mm Screw Diameter with 90 Kw Motor twin screw extruder with a output ranging from 380 to 475 Kg/hr. Complete PLC......

The standard molding conditions for our materials are shown below. Please click the mouse at the following names of plastics.

The screw is rotated to melt plastic introduced from the hopper and to accumulate molten plastic in front of the screw ( to be called metering ) . After the required amount of molten plastic is accumulated, injection process is stared.

Sprues and runners among moldings are not products. These portions are sometimes discarded, but in other cases they are finely reground and reused as materials for molding. These materials are called reprocessed materials.

Our company is into manufacturing of fillers and compounds since 2006 We have 3 running lines - 1 Single screw Kneader and 2 Twin screw extruders with Under water pelletizers Total In......

A molding consists of a sprue to introduce molten resin, a runner to lead it to cavities, and products. Since obtaining only one product by one shot is very inefficient, a mold is usually designed to have multiple cavities connected with a runner so that many products can be made by one shot.

Password must be between 4 and 15 characters long, and may consist of hyphen (-), underscores (_), dot (.), and asterix (*).

We are a leading blow moulder and are in search of a closed unit or a running business involved in manufacturing of blow moulded packaging items upto the size of 10 liters. We prefer bu......

Kolsite PVC Pipes Type: 52/25 No.: 2 Production capacity: 150 mt/month (both) Type: 65/22 No.: 1 Production capacity: 150 mt/month Type: 90/22 No.: 1 Production capacity: 2......

For the properties when reprocessed materials are used, please refer to "reprocessing capability" in the plastic data base.

The position of change from speed control to pressure control is set at the point where either screw position or injection pressure reaches a certain fixed value.

We use cookies on this website to ensure your user experience. Please click the button if you agree to the use of cookies. When you keep browsing this website, this will also mean that you are giving consent to the use of cookies.

Complete Metallising facility for sale which includes the following equipment plus approximately 100 tons per month of existing business. - 1700 mm Galileo Metallizer - 1675 mm Polytype......

Running plant for Sheets WE HAVE SOPHISTICATED PLC CONTROLLED CO-EX SHEET PLANT. WE CAN PRODUCE SHEETS OF PP, HIPS, HDPE AND ABS UPTO 1450 MM WIDTH AND THICKNESS FROM 0.45 MM TO 6.5 MM......