Focusing on one type of machine also contributes to the goal of maximum production stability. "The CC300 control unit of the ENGEL machines with its large display is genuinely intuitive to operate and helps us achieve great process stability. And at the end of the day, that gives us better quality." points out Eric Biguet, a set-up technician responsible for smooth production operations. "

"E-flomo helps us respond quickly if the flow stalls in a circuit," says Branchereau. "That gives us a good safety margin, especially at night when there are fewer machine operators on duty."

Six moulds, for three different cylinder diameters, are currently deployed in cylinder production at L'Arbresle. In total, the FX dialysers are available in five sizes. The version used depends on the patient's size and weight. A mould change is scheduled at least once a week. This was already taken into account in the design of the machines. The e-flomo electronic temperature control water manifold systems, for example, were installed outside the mould area to allow flexible mounting of different sized moulds. Each mould has a different number of cooling circuits.

Today, 26 e-motion injection moulding machines – each with a clamping force of 2200 kN – are deployed in the cleanroom. They all operate 24/7 with a utilisation of well over 90%.

"We have developed new closures with a core made of glass-fibre-reinforced polypropylene," Alain Philibert reports. "They are so robust that we can reuse them up to 50 times."

Until she retired in September 2021, Clare Goldsberry reported on the plastics industry for more than 30 years. In addition to the 10,000+ articles she has written, by her own estimation, she is the author of several books, including The Business of Injection Molding: How to succeed as a custom molder and Purchasing Injection Molds: A buyers guide. Goldsberry is a member of the Plastics Pioneers Association. She reflected on her long career in "Time to Say Good-Bye."

"iQ clamp control is particularly interesting for us," says Philibert citing an example. The smart assistance system determines the optimum clamping force for the injection moulding process in question. In most cases, the optimum clamping force is lower than the value set manually. Clamping force correction then not only improves quality consistency, but also saves energy. The trend towards greater sustainability has long since arrived in medical technology, too, and not just following the rapid rise in energy prices.

Energy efficiency, but also material efficiency, is a focus of continuous product development at Fresenius. You can see one example of this by following the path of freshly injection moulded dialyser housings. After a short interim storage period, they are filled with the hollow fibres, which are also produced on-site, and tightly sealed with yellow lids made of polyurethane. It is only after steam sterilisation that the yellow lids are replaced by functional closures in blue polypropylene. The polyurethane lids are disposable parts, and that is precisely what is due to change.

The lives of two and a half million people with chronic kidney failure depend on what look like inconspicuous plastic cylinders at first glance: dialysers are the central element in dialysis (artificial kidney) machines. On closer inspection, the FX-class series dialysis cartridges by Fresenius Medical Care are highly sophisticated. They contain up to 20,000 hollow fibres as wide as a hair with microscopic pores, through which toxins, urea, excess salts and water are removed from the blood during haemodialysis. The process takes four hours. The patients need to be connected to the machine three times a week.

The repositioning of the accelerator does not take place directly through the clamp plate but through a cut-to-length ejector, so the same buffer plates for the ejector set can be used. A further advantage is that the entire injection pressure is absorbed directly by the ejector base plate. As a result, the ejector accelerator does not bear any load during the injection molding process, explained Meusburger.

"The e-motion machines ensure high dimensional accuracy across all cavities," as Branchereau points out. "This is all the more important because we assemble the cartridges in a fully automated process."

Each FX-class filter cartridge needs six thermoplastic components, which Fresenius Medical Care SMAD injection moulds in L'Arbresle, about 20 kilometres northwest of Lyon. The components include the transparent cylindrical housing and the blue caps that seal the cylinder with the hollow fibre bundle at the top and bottom and house the connections for the dialysis fluids.

"In-house production makes us more flexible," as technical director Thibaud Robin-Rivoire explains. "We can very easily adapt products to our customers' requirements, especially since these requirements regularly change."

The material poses a further challenge because PP has a lot of shrinkage. On the other hand, it offers benefits in other areas. While filter housings are often produced from polycarbonate, Fresenius Medical Care deliberately chose polypropylene because it is significantly lighter and therefore boosts efficiency in both logistics and waste management.

According to its own statements, Fresenius Medical Care is the world market leader in the treatment of kidney disease. "At least one Fresenius Medical Care product is involved in every second dialysis performed worldwide," explains the project manager, Alain Philibert.

Three different sizes allow designers to install ejectors in diameters of 3 to 11.5 mm at will. The small component size enables flexible positioning of the ejection accelerator in the ejector set, allowing quick and easy retrofitting. In order to save design time, the installation space is already included in the CAD data. The new component is available from stock.

The cylindrical filter housings are particularly demanding. They are injection moulded from polypropylene in a 4-cavity mould. The wall thickness is 1.5 mm throughout, but the filigree structures at the ends, each with a circular undercut, require a sophisticated injection profile to be completely filled. Injection takes place from two sides at the centre of the cylinder. There are two core pulls for each cavity that move out to the left and right respectively for part removal.

In the production of plastic components for dialysis products in the cleanroom, maximum precision is required for every shot. The task is to combine precision with process stability and cost effectiveness. Fresenius Medical Care masters this challenge with all-electric high-performance injection moulding machines by ENGEL.

The new E 1522 Ejector accelerator from Meusburger (Wolfurt, Austria) optimizes the smooth ejection of injection molded parts and promises safe and targeted ejection of complex parts. The acceleration ratio is 1:1.5, achieving a longer path with a small stroke. Through the additional acceleration of a single ejector, “snagging” of the injection molded part is avoided.

"We have to be able to rely on the machines' repeatability, and we need maximum precision and absolute cleanliness," says Laurent Branchereau, head of the injection moulding shop at the plant, explaining the choice of machines. Every four hours, random samples of the parts are visually inspected and the critical dimensions are measured.

The top priority is uncompromising quality, and it was also a quality-driven decision to exclusively equip the location with all-electric injection moulding machines from ENGEL's high-performance e-motion series.

"ENGEL also customises the machines to meet highly individual requirements. That's what characterises our collaboration with ENGEL." emphasises Robin-Rivoire. Digital solutions, such as the iQ smart assistance systems from the inject 4.0 program, are currently being evaluated.